Process Measurement, Instrumentation & Control

In an industrial situation where it is required to measure and control some aspects of a process, it is often the application of the knowledge and the ingenuity of the Engineer or Technician which is relied upon to solve the measurement and control problem.

Electrical & Power Engineering · 5 Days · Public · Al-Khobraa certified · From USD 3,900

Learning Objectives

  • To give an understanding of the principles of operation of a range of sensors and transducers
  • By using a hands-on approach, enable the delegate to investigate the operation of an instrumentation system through designing, building and testing a typical sensor combined with appropriate signal conditioning circuits
  • To allow the delegate to become familiar and confident with a range of measurement techniques
  • To understand the concepts of Process Control and acquire the knowledge relating to the characteristics and properties of a process variable being measured
  • To become familiar and knowledgeable with PID control and develop the ability to ‘tune’ a process control system using PID control
  • To have the confidence and knowledge to apply the above techniques and principles to solve an unfamiliar and bespoke measurement situation in the workplace

Who Should Attend

This training course will be of benefit to the roles listed below.

  • Electronic Engineers and Technicians
  • Chemical Engineers and Technicians
  • Electrical Engineers and Technicians
  • Electronic Design Engineers
  • Instrumentation Technicians
  • Electricians
  • Installation and Maintenance Technicians
  • Instrument and Process Control Technicians
  • Maintenance Engineers
  • Mechanical Engineers and Technicians

Course Outline

Day 1 — Introduction to Sensors, Transducers and Instrumentation Systems

  • Course Schedule and Layout
  • Introduction to Sensors, Transducers and Instrumentation Systems
  • Examples
  • Terms and Definitions Associated with Instrumentation Systems, including

Day 2 — Strain, Pressure, and Flow Measurement (also begin practical activities)

  • Principle of Strain Measurement – tension, compression, stress, strain, Youngs modulus
  • Principle of Operation, Typical Uses and Installation Considerations
  • Gauge Types – Principle of Operation and Configurations
  • Examples

Day 3 — Temperature, Level and Non-Invasive Ultrasonic Measurement Techniques

  • Temperature Scales
  • Devices: Principle of Operation - Typical Uses and Installation Considerations of
  • Resistance Temperature Detectors (RTD’s) Thermistors
  • Thermocouples

Day 4 — Introduction to Process Control Engineering

  • Control Strategies
  • Block Diagram Representation
  • Control Components
  • Servomechanisms and Regulators

Day 5 — Tuning PID Controllers

  • Empirical Methods of Setting Controllers
  • Open Loop Reaction Curve Method (Ziegler-Nichols)
  • Default and Typical Settings
  • Closed Loop Continuous Cycling Method (Ziegler-Nichols)

Accreditation

Al-Khobraa certified. On completion delegates receive an Al-Khobraa certificate of achievement.

Dates & Venues

DatesVenueDeliveryDurationFee (USD)
December 21–25, 2026Accra, GhanaPublic5 days4,500

Inquire about Process Measurement, Instrumentation & Control · Inquire on WhatsApp

Frequently Asked Questions

What do Al-Khobraa electrical and power engineering courses cover?

The portfolio covers power generation, transmission and distribution, low- and high-voltage systems, power system protection and relay coordination, switchgear and transformers, motors and drives, SCADA and smart grids, and electrical safety and arc-flash control.

Who should attend an electrical or power engineering course?

These courses suit electrical engineers and technicians, substation and grid operators, protection and control specialists, maintenance supervisors, plant and facilities engineers, and utility or contractor staff working on generation, transmission or distribution assets.

How long are electrical and power engineering courses, and where are they held?

Most Al-Khobraa electrical and power engineering courses run over 5 days. The exact duration, dates and city for this course are listed in the dates section on this page. Public sessions run across Saudi Arabia — Riyadh, Jeddah, Al-Khobar, Jubail and Yanbu — as well as regional and international venues, with live virtual classrooms available on request.

What certificate will I receive?

Delegates who complete the course receive an Al-Khobraa certificate of completion, issued by a Saudi-registered training provider. Al-Khobraa also delivers internationally accredited programs; where a course carries an external awarding body such as PMI, CIPS, ILM or IOSH, that body is named on the course's own page.

Can electrical and power engineering training be delivered in-house for our team?

Yes. Any Al-Khobraa electrical and power engineering course can be delivered in-house at your own premises anywhere in Saudi Arabia or the GCC, with the content, dates and language of delivery tailored to your team. Al-Khobraa is an approved HRDF (Hadaf) provider, so eligible Saudi employers can seek training support. Contact us for a quotation.

Related Electrical & Power Engineering Courses

Browse all Electrical & Power Engineering training courses