Electrical Equipment & Control Systems: Commissioning, Testing & Start-Up of Electrical Systems

Equipment readiness for commercial service is proven by testing all its functions under different conditions. ‘Do not believe, until it is proven’ is the key to successful testing and satisfactory operation of electric systems. Equipment is finally proven when it is energized and tested on load during the start-up (first energization).

Electrical & Power Engineering · 5 Days · Public · Al-Khobraa certified · From USD 3,900

Learning Objectives

  • A better understanding of commissioning procedures
  • A better understanding of troubleshooting procedures
  • An improved capability in the use of test equipment
  • A better understanding of failure modes and failure analysis
  • Understand the testing process
  • Plan and prepare for testing
  • Plan and carry out inspections
  • Perform primary and secondary injections
  • Plan the first energization
  • Perform phasing tests
  • Consider safety aspects during testing
  • A refreshed awareness of electrical safety concerns

Who Should Attend

This training course is suitable for a wide range of professionals but will greatly benefit: Testing Engineers / Technicians Maintenance Engineers / Technicians Managers of Engineering departments Consulting Engineers / Technicians Project Engineers Safety Professionals Others who want a solid preparation in testing & commissioning

  • Testing Engineers / Technicians
  • Maintenance Engineers / Technicians
  • Managers of Engineering departments
  • Consulting Engineers / Technicians
  • Project Engineers
  • Safety Professionals

Course Outline

Day 1 — Importance of Start-Up, Commissioning, and Testing of Electrical Systems  Definition of Start-up, Commissioning, and Testing Pre-commissioning Procedures Reasons for Start-up, Commissioning, and Testing Substation Commissioning – Gas Insulated Substation Managing Commissioning with IEC 61850 and GOOSE Earthing System including Clean Earth, Intrinsic Safe Earth, and Planet Earth Major Components of GIS Substations GIS with Vacuum Interrupter The Technology of Electrical Equipment

  • Transformers – Power supplies (UPS) – Batteries
  • Generators – Switchgear – Disconnect switches
  • Neutral ground resistors (NGR)
  • Motor control centers (MCC) – Variable frequency/speed drives (VFD/VSD)

Day 2 — Commissioning Test Equipment (CPC 100, Omicron 356, CIBANO, ARCO, TESTRANO) and Circuit Breakers including Instrument Transformers

  • Types of Tests and Equipment for Commissioning
  • IR test, Primary Injection Test, Secondary Injection Test
  • HV Test, AC Hipot Test, DC Hipot Test and Connections
  • Infrared and Partial Discharge Monitoring

Day 3 — The Use of Test Equipment

  • Digital voltmeter (DVM)
  • Megger
  • Frequency meter
  • Temperature probes/pyrometers

Day 4 — The Development of a Job Plan

  • Identification of the troubleshooting step-by-step sequence
  • Procedure preparation
  • Follow-up
  • Safety considerations and training

Day 5 — First Energization and Commissioning Documentation

  • Battery Charger Commissioning Tests
  • Commissioning Switching Plans
  • Managing the First Energization
  • Switching Plans

Accreditation

Al-Khobraa certified. On completion delegates receive an Al-Khobraa certificate of achievement.

Dates & Venues

DatesVenueDeliveryDurationFee (USD)
December 13–17, 2026Dubai, UAEPublic5 days3,900
December 21–25, 2026Cape Town, South AfricaPublic5 days4,500
March 28 – April 1, 2027Dubai, UAEPublic5 days3,900
June 13–17, 2027Dubai, UAEPublic5 days3,900
August 15–19, 2027Dubai, UAEPublic5 days3,900
December 12–16, 2027Dubai, UAEPublic5 days3,900

Inquire about Electrical Equipment & Control Systems: Commissioning, Testing & Start-Up of Electrical Systems · Inquire on WhatsApp

Frequently Asked Questions

What do Al-Khobraa electrical and power engineering courses cover?

The portfolio covers power generation, transmission and distribution, low- and high-voltage systems, power system protection and relay coordination, switchgear and transformers, motors and drives, SCADA and smart grids, and electrical safety and arc-flash control.

Who should attend an electrical or power engineering course?

These courses suit electrical engineers and technicians, substation and grid operators, protection and control specialists, maintenance supervisors, plant and facilities engineers, and utility or contractor staff working on generation, transmission or distribution assets.

How long are electrical and power engineering courses, and where are they held?

Most Al-Khobraa electrical and power engineering courses run over 5 days. The exact duration, dates and city for this course are listed in the dates section on this page. Public sessions run across Saudi Arabia — Riyadh, Jeddah, Al-Khobar, Jubail and Yanbu — as well as regional and international venues, with live virtual classrooms available on request.

What certificate will I receive?

Delegates who complete the course receive an Al-Khobraa certificate of completion, issued by a Saudi-registered training provider. Al-Khobraa also delivers internationally accredited programs; where a course carries an external awarding body such as PMI, CIPS, ILM or IOSH, that body is named on the course's own page.

Can electrical and power engineering training be delivered in-house for our team?

Yes. Any Al-Khobraa electrical and power engineering course can be delivered in-house at your own premises anywhere in Saudi Arabia or the GCC, with the content, dates and language of delivery tailored to your team. Al-Khobraa is an approved HRDF (Hadaf) provider, so eligible Saudi employers can seek training support. Contact us for a quotation.

Related Electrical & Power Engineering Courses

Browse all Electrical & Power Engineering training courses